Audi Quattro Ultra binding issue
We have previously discussed the evolution and different types of Audi's famous all-wheel-drive system, Quattro, over the years in our previous article. Having used the full-time all-wheel-drive Torsen system for many years in its models with longitudinally mounted engines, the brand transitioned in 2016 to the Ultra system, which conceptually resembles Haldex and sends power to the rear only when necessary. Aiming to reduce fuel consumption, this system has the transmission connected directly to the front axle, and there is no center differential. As we wrote back then:
Ultra is more complex than Haldex due to the synchronization process: before AWD kicks in, the driveshaft needs to be spun up by the first clutch, and then a second clutch connects it to the rear differential... there are many parts that can break.
What Goes Wrong?
Quattro Ultra uses an electronically controlled multi-plate clutch module located at the rear of the transmission. The problem occurs in this clutch pack: over time, the clutch plates wear out, the fluid in between creates sludge, and the plates start to stick/bind together. A severe shuddering, binding, and clunking are felt in the vehicle, especially at low speeds, during tight turns with the steering wheel at full lock, or in narrow parking maneuvers. The issue has entered the literature and foreign forums as Quattro Rumble or Quattro Ultra Binding.
Noticed by a humming sound coming from the rear-center of the vehicle starting from 40-50 thousand km, authorized service centers generally address this problem in the following order:
- Software Update and Calibration: Initially, the system's torque transfer values are recalibrated via software. If the plates are not severely damaged, this new software can temporarily resolve the shuddering by changing the torque distribution tolerances.
- AWD Clutch Fluid Change and Adaptation: If the software doesn't work, the fluid in the clutch system (transfer case) is replaced. After putting in the new fluid, the service technician takes the car and drives in figure-eights or full circles to "sand/polish" the rough spots and residue on the plates with the new fluid. Although many users think the problem is solved at this stage, it generally recurs after a while.
- Clutch Module Replacement: If the fluid change and adaptation drive also fail to stop the shuddering, it means the clutch plates are too worn or burnt to be saved. At this point, the entire AWD clutch module is replaced with a new one.
Technical Service Bulletins
There are 8 different service bulletins related to this issue published by Audi in the US and Europe from 2020 to 2026:
- December 10, 2020: The problem is defined as the vehicle displaying an "All-wheel drive system fault" due to a worn or faulty Quattro Ultra shift fork located inside the rear differential: Audi instructs technicians not to replace the entire rear differential. Instead, they are required to use new shift forks manufactured with improved materials.
- February 26, 2021: The repair is tied to two stages: First, the technician is told to change the fluid in the AWD clutch unit and take the vehicle for 3 separate test drives (adaptation) to calibrate the system. If this fluid change and test procedure do not stop the clunking, they are ordered to remove the driveshaft and completely replace the rear AWD clutch unit with a new one.
- November 2, 2022: This details the "Quattro Rumble" (clutch shudder) procedure mentioned above. The most notable instruction in the bulletin is the expansion of the repair scope because this process was deemed insufficient for vehicles where previously only a fluid change was attempted. In other words, if the fluid calibration doesn't work, approval is given to intervene with the part itself.
- May 9, 2023: Unlike the others, this bulletin does not contain mechanical removal-installation or part replacement instructions. To solve the problem, service centers are instructed to perform a software update directly via SVM (Software Version Management). The software calibration of the control module managing the system is revised.
- October 9, 2023: In this document, technicians are told to perform a software update, followed by changing the fluid in the AWD module and doing an adaptation drive. It states that if unresolved, the clutch module will be replaced.
- October 21, 2024: The technician is told to directly apply the "Overheating AWD Clutch Unit" calibration for troubleshooting or repair. The goal is to force the system by having the customer's vehicle continuously driven in circles until the overheating warning appears on the screen; this aims to sand down the residue on the worn plates through friction.
- May 22, 2025: A direct reference is made to the change in the friction surfaces of the AWD clutch pack. As a solution, the technician is instructed to turn the steering wheel to full lock and drive in circles at 10 km/h until the "All-wheel drive system overheated" warning appears on the screen. The aim is to sand down the residue on the plates with its own fluid and friction.
- January 26, 2026: To avoid part replacement and labor costs, Audi has further extended the procedure, mandating the "Double Fluid Change" method. The technician completely drains the system, adds new clutch fluid (G 055 515 A2), brings the transmission up to operating temperature, lets the vehicle cool down, then drains the fluid again and adds fresh fluid a second time.
Which Audis Have Quattro Ultra?
These problems, most commonly seen in Turkey in C8 chassis (2019–2025) A6 40 TDI/45 TFSIs, can also occur in B9 A4-A5 and FY Q5s (2016–2025).
- GH0 - no rear differential, front-wheel drive
- GH1 - open rear differential, Torsen
- GH2 - sport rear differential, Torsen/crown gear
- GH4 - open rear differential, quattro ultra

6 Comments